- 您现在的位置：买卖IC网 > Sheet目录17374 > B048F480T30-EB (Vicor Corporation)EVAL BOARD 48V OUT 300W SMD
Not Recommended for New Designs - Replaced by BCM48Bx480y300A00
Application Note
B048F480T30
Parallel Operation
The BCM ? bus converter will inherently current share when operated in
an array. Arrays may be used for higher power or redundancy in an
application.
Current sharing accuracy is maximized when the source and load
impedance presented to each bus converter within an array are equal.
The recommended method to achieve matched impedances is to
dedicate common copper planes within the PCB to deliver and return
the current to the array, rather than rely upon traces of varying lengths.
In typical applications the current being delivered to the load is larger
than that sourced from the input, allowing traces to be utilized on the
input side if necessary. The use of dedicated power planes is, however,
preferable.
The bus converter power train and control architecture allow bi-
directional power transfer, including reverse power processing from the
module output to its input. Reverse power transfer is enabled if the
module input is within its operating range and the module is otherwise
enabled. The bus converter’s ability to process power in reverse
improves the module’s transient response to an output load dump.
Thermal Considerations
VI Chip products are multi-chip modules whose temperature
distribution varies greatly for each part number as well as with the
input /output conditions, thermal management and environmental
conditions. Maintaining the top of the B048F480T30 case to less than
100°C will keep all junctions within the module below 125°C for most
applications. The percent of total heat dissipated through the top
surface versus through the J-lead is entirely dependent on the particular
mechanical and thermal environment. The heat dissipated through the
top surface is typically 60%. The heat dissipated through the J-lead
onto the PCB board surface is typically 40%. Use 100% top surface
dissipation when designing for a conservative cooling solution.
It is not recommended to use a module for an extended period of time
at full load without proper heat sinking.
Input Impedance Recommendations
To take full advantage of the BCM bus converter capabilities, the
impedance presented to its input terminals must be low from DC to
approximately 5 MHz. The source should exhibit low inductance and
should have a critically damped response. If the interconnect inductance
is excessive, the module input pins should be bypassed with an RC
damper (e.g., 47 μF in series with 0.3 ohm) to retain low source
impedance and proper operation. Given the wide bandwidth of the
module, the source response is generally the limiting factor in the
overall system response.
Anomalies in the response of the source will appear at the output of
the module multiplied by its K factor. The DC resistance of the source
should be kept as low as possible to minimize voltage deviations. This is
especially important if the module is operated near low or high line as
the overvoltage /undervoltage detection circuitry could be activated.
Input Fuse Recommendations
VI Chip modules are not internally fused in order to provide flexibility in
configuring power systems. However, input line fusing of the modules
must always be incorporated within the power system. A fast acting
fuse should be placed in series with the +In port.
BCM ? Bus Converter
Page 10 of 12
Rev 3.4
01/2014
vicorpower.com
800 927.9474
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
GBM10DRYN-S13
CONN EDGECARD 20POS .156 EXTEND
RO-0524S/P
CONV DC/DC 1W 05VIN 24VOUT
A9BAG-1305F
FLEX CABLE - AFF13G/AF13/AFE13T
B048F320T30-EB
EVAL BOARD 32V OUT 300W SMD
MAX4824ETP+
IC 8CH RELAY DVR PWR SAVE 20TQFN
B048F240T30-EB
EVAL BOARD 24V OUT 300W SMD
GEM08DRYI-S13
CONN EDGECARD 16POS .156 EXTEND
A9AAT-1806F
FLEX CABLE - AFE18T/AF18/AFE18T
相关代理商/技术参数
B048G120T10
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI Chip - BCM Bus Converter Module
B048G120T15
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI Chip - BCM Bus Converter Module
B048K030M21
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI Chip - BCM Bus Converter Module
B048K030T21
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI Chip - BCM Bus Converter Module
B048K060M24
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI Chip - BCM Mus Converter Module
B048K060T24
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI Chip - BCM Mus Converter Module
B048K096M24
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI ChipTM - BCM Bus Converter Module
B048K096T24
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI ChipTM - BCM Bus Converter Module